vortex flow meter application

When the pipe is in a horizontal position the liquid phase tends to flow at the bottom of the pipe and therefore the inside of the pipe. They are to be seen as first choice subject to verification to cover the requirements of a particular application.

Vortex Flowmeter Design Main Parts Vortex Mechanical Force Metering

For low-viscosity products such as water gasoline and liquid ammonia the maximum application speed is 15fts 46ms the vortex flow meter has an adjustable range of about 201 and the pressure loss is about 4PSIG 274 kpa.

. A display is highly recommended for any fine tuning adjustments required. Application Of Vortex Flow Meter. Vortex meters are essentially frequency meters since they measure the frequency of vortices generated by a bluff body orshedder bar.

It works on the principle of moving the fluid through the pipe where the highly sensitive sensors are planted to measure the velocity of the fluid. When the fluid passes through it disturbances in the flow called vortices are alternately formed on both sides of the shedder. The inline flow meter works the way it has been discussed above.

When installing a vortex flowmeter to measure biogas if a valve is installed near the upstream of the installation point and the valve is constantly opened and closed it will have a great impact on the service life of the sensor. Vortex Flow Meter Installation. Saturated steam superheated steam compressed air nitrogen liquefied gases flue gases carbon.

Steam injection involves generating steam on the surface and forcing this steam down injection. The vortex flowmeter is a broad-spectrum flow meter which can be used for metering measurement and control of most steam gas and liquid flow for a very unique medium versatility high stability and high reliability with no moving parts simple structure and low failure rate. The requirement that there be turbulent flow and force sufficient to actuate the sensor determines the meters rangeability.

Inline Vortex Flow Meter. Vortex flow meter application on low-quality wet steam is one such application. When installing a vortex flowmeter to measure biogas if a valve is installed near the upstream of the installation point and the valve is constantly opened and closed it will have a great impact on the service life of the sensor.

This force has to be high enough to be distinguishable from noise. Tek-Vor 1300C Vortex Flow Meter is a versatile instrument that calculates the mass flow volumetric flow rate temperature pressure and density of any liquid gas or steam through a pipeline. Application of vortex flow meters in Shells oil gas and liquefied natural gas projects is an accepted practice.

Flow Meter Application Advisor. Liquids gases and steam. As these vortices are shed from the bluff body they create alternating low and high pressure zones that oscillate at particular.

The application of a vortex flow meter to low-quality wet steam is one such application. The liquid phase must be uniformly dispersed in the vapor and vertical flow lines must be avoided to prevent slugging. Vortex flow meters also excel in steam-related applications including steam injection and steam measurement for district energy systems and industrial plants.

Vortex steam flow meter is mainly used for measuring saturated steam superheated steamwet steam dry steam dry gas wet gasetccan measure highest temperature around 350. The force generated by the vortex pressure pulse is a function of fluid density multiplied by the square of fluid velocity. The vortex flowmeter can display the instantaneous flow and cumulative flow of biogas.

Vortex flow meters are well suited for a variety of applications across a wide range of industries including oil and gas refining chemical and petrochemical and food and beverage. The measured medium temperature is -20150 -40250 100350 tube only. Reducer Vortex meter body sizes.

Volume flow measurement is enough for substances with small variations in density such as liquid. Rosemount 8800 Weld-end vortex flow meter. However key to a fit-for-purpose performance of vortex flowmeters is.

The inner diameter of the vortex flow sensor is 25-300mm full tube Plug-in vortex flow sensor application inner diameter range is 350-1200mm plug-in The accuracy of measuring liquid with full tube is 1 and the accuracy of measuring steam and gas is 15. Shanghai cixi instrument COLTDa professional 35 years manufacturer of micro flow meterultrasonic flow meterwater flow metermagnetic flow meterturbine flow metervortex flow metercoriolis flow meterdigital flow meterthermal mass flow meterliquid flow meterair flow meterdosing pumpgear metering pumplevel meterlevel sensor etc. Rosemount 8800 Wafer vortex flow meter Lightweight cost-effective solution Easy installation with standard alignment rings Ideal for utility applications Available with ½ inch through 8 inch 15 mm through 200 mm line sizes.

The application of a vortex flow meter to low-quality wet steam is one such application. Vortex flow meters have been appreciated by users as volume flow meters which can in principle be applied to any flow measurement of liquid gas or steam. Multivariable vortex flowmeters also have the capability of measuring mass flow and this makes them attractive especially for steam and gas flow measurement.

Vortex flow meters are a direct type of flow-measuring device with operating fundamentals based on the Von Karman Vortex Street principle. The producing wells then pump up the oil and water. The vortex flowmeter can display the instantaneous flow and cumulative flow of biogas.

Applications in the chemicals and petrochemicals industries for example in power generation and heat-supply systems involve widely differing fluids. It finds widespread application in several industries including Petrochemical Chemical Pharmaceutical Food and Beverage Water and Wastewater Treatment. However for compressed gases the vortex meter has low flow and low-pressure limitations.

It is the popular form of the vortex flow meter. Vortex flow meters use an obstruction known as a bluff body in the flow stream to create downstream vortices which are alternately formed on either side of the bluff body. With water flooding injected water enters the reservoir and displaces some of the remaining oil toward producing wells in the same reservoir.

The liquid phase should be homogeneously dispersed within the steam and vertical flow lines should be avoided to prevent slugging. The vortex flowmeter is relatively economical because of its simple. The inner diameter of the vortex flow sensor is 25-300mm full tube Plug-in.

Multiple mounting types available Vortex flowmeters are available in flanged wafer and insertion styles. Vortex Meters can be used for a wide range of fluids ie. When the pipe is in a horizontal position the liquid phase tends to flow at the bottom of the pipe and therefore the inside of the.

Vortex flowmeters are used in numerous branches of industry to measure the volume flow of liquids gases and steam. Steam measurement is the most popular application for vortex flow meters as they are far more economical and easy to install versus other flow measurement technologies that have the ability to measure steam. All the vortex meters are custom built to order.

In this instrument a bluff body or shedder bar is arranged at the center of flow path.

Pin On 仪器仪表